LTP5500DCNC Non-Touch Pilot Arc Plasma Cutter
- 3/5 inch (15 mm) cut, 15 lbs weight
- 20-55 A DC output on 220/240V
- 3/5 inch clean cut, 1 inch severance on 220/240V
- 3/8 inch clean cut, 1/2 inch severance on 110/120V
- 110~125V or 215~245V, automatic dual voltage
- 70 PSI at 4.0 SCFM air supply
- CNC interface with THC signal, Non-HF blowback start
Updated 2 days ago · Based on the Amazon listing and published specifications, not hands-on testing.
A light dual voltage plasma cutter with a CNC interface for home and light business work. The listing gives torch cable length twice with different figures.
As an Amazon Associate I earn from qualifying purchases. ProductDome earns a commission when you buy through links on this page.
ASIN: B0H9L18M4XModel: LTP5500DCNCCategory: Plasma Arc Cutting Equipment
Overview
The LTP5500DCNC is a non-touch pilot arc plasma cutter that weighs little enough to carry between jobs. It has a pre-installed air filter regulator and plug, and a CNC interface sends a torch height signal to a plasma table.
Running on household or shop voltage with a quick air hookup makes this easy to set up. The limit is thickness on the lower input and the CNC cutting limit, both well below the full hand-cut rating.
Who it's for
Garage fabricators and small businesses cutting mild steel, stainless, copper or aluminum will use the dual voltage input. A production shop with thick plate should size up.
Pros and cons
- Light enough to carry
- Dual voltage, automatic
- Non-HF blowback start
- CNC interface with THC output
- Torch cable length stated twice differently
- CNC cut thickness lower than hand cut
- Lower thickness on 110V
Performance notes
The thickness it cuts follows the input voltage and output current: the higher voltage gives the full clean cut and the lower voltage is limited. The blowback start avoids high frequency interference near a CNC computer. A steady supply of compressed air at the stated pressure and flow is needed for a stable arc.
Specifications
| Model | LTP5500DCNC |
|---|---|
| Dimensions & fit | |
| Weight | 15 lbs |
| Capacity & performance | |
| Output on 220/240V | 20-55 A DC; 3/5 inch clean, 1 inch severance |
| Output on 110/120V | 20-35A DC; 3/8 inch clean, 1/2 inch severance |
| Power & efficiency | |
| Input voltage | 110~125V or 215~245V, automatic dual voltage |
| Included components | |
| Included | IGBT inverter power supply, CNC cutting straight torch with 20ft cable, consumables, ground clamp, NPT 1/4 inch Type D plug, air filter regulator |
| Other details | |
| Cutting capacity | 3/5 inch (15 mm) |
| Air requirement | 70 PSI at 4.0 SCFM |
| Recommended breaker | 110V at 50A and 220V at 40A |
| Start type | Non-HF blowback pilot arc |
| CNC cutting thickness | 1/4 inch |
Frequently asked questions
How do I get the LTP5500DCNC ready to cut?
A pre-installed NPT 1/4 inch industry type D plug and air filter regulator quick connect to your compressor coupler. The listing says the machine can be set up within 1 minute.
Can the LTP5500DCNC run on household power?
Yes. It takes 110~125V or 215~245V automatically, with a lower cut thickness on 110/120V.
What breaker and air supply does it need?
A 50A breaker at 110V or a 40A breaker at 220V, and an air compressor giving 70 PSI at 4.0 SCFM.
How thick can it cut with a CNC table?
The listing gives a CNC cutting thickness of 1/4 inch.